Homey Community Forum

[APP] Systemair

Systemair support for Athom Homey

With this app and a Systemair Z-wave adapter or a Systemair Internet access module (IAM), you can control your Systemair HVAC.

You can control the set point temperature, set the fan mode and mode.

App store: https://homey.app/no-no/app/com.systemair/Systemair/
Test-version: https://homey.app/no-no/app/com.systemair/Systemair/test/
Source: https://github.com/balmli/com.systemair

Device: Systemair IAM Cloud

This device supports the Systemair Internett access module in “Cloud” mode. “Modbus TCP” mode is not supported.

Triggers

  • Set point temperature was changed
  • Temperature changed
  • Humidity changed
  • Fan mode changed
  • Mode changed

Conditions

  • Fan mode is
  • Mode is

Actions

  • Set temperature
  • Set fan mode
  • Set mode
  • Initiate boost mode
  • Initiate away mode
  • Initiate crowded mode
  • Initiate fireplace mode
  • Initiate holiday mode
  • Initiate refresh mode

Device: Systemair Z-wave

This devices supports the Systemair Z-wave adapter.

Triggers

  • Alarm (tokens: info)

Actions

  • Set fan mode
  • Set mode
  • Initiate boost mode

Acknowledgements:

Thanks to https://github.com/perara/python-systemair-savecair for communicating with the Systemair IAM.

Disclaimer:

Use at your own risk. I accept no responsibility for any damages caused by using this app.

Release Notes:

0.9.7

  • Systemair IAM Cloud: view Mode and Fan mode as sensors

0.9.6

  • Systemair IAM Cloud: added conditions for fan mode and mode
  • Systemair IAM Cloud: added triggers for fan mode changed and mode changed
  • Systemair IAM Cloud: added boost mode
  • Systemair IAM Cloud: added modes for Away, Crowded, Fireplace, Holiday and Refresh

0.9.5

  • Systemair IAM Cloud: fixed icon

0.9.4

  • Systemair IAM Cloud: fixed an issue about setting modes between Auto and Manual
  • Systemair IAM Cloud: added check for IAM / password when adding the device
  • Systemair IAM Cloud: added polling interval to Advanced settings. Default is 30 seconds.
  • Fixed README
  • Renamed ‘Systemair HVAC adapter’ to ‘Systemair Z-wave’

0.9.3

  • Initial support for the Internet Access Module (Cloud)

0.9.2

  • Fixed ‘Set fan mode’ action

0.9.0

  • First version for app store
3 Likes

To be able to view Mode and Fan mode, the device must be reinstalled.

Is it possible to have exhaust air temperature visible in the app - and also as a sensor? I control my system with the temperature of the extracted air. Thanks:-) God påske!

Yes! Will fix this.

And when activating boost mode - it goes to manual (visible in the systemair app) AND does not revert to Auto after end of boost time. I wonder why?

Version 0.9.8 ready for test:

  • Systemair IAM Cloud: added Extract air temperature
  • Systemair IAM Cloud: added Outdoor, Supply and Extract temperature changed triggers!

The current “boost mode” implementation stores the mode (auto / manual) and the fan mode when the boost mode is activated.

When the period for the boost mode is over, the mode and fan mode are set back to the state they had.

But, this can easily be changed of course :slight_smile:

OK!

That sounds good - then I must try again to see if that works :slight_smile:

I do want it to go back to the previous state

Thanks!

Does extract air temp work as expected, @Amund ?

Yes indeed!

I’m working with a friend to really connect the systemair with the NIBE water-water and all of the temperature sensors in the house.

This app was the last bit missing.

Thank you!

I see that the app is slow on updating the fan state.

Takk! Amund

It’s possible to change the polling interval from Advanced settings. The default is 30 seconds. You can set the minimum, if you want, to 10 seconds.

OK! As you see the mode and fan speed updates are not updating - the other values are as expected

See picture:

OK, thanks.

I will try to fix :slight_smile:

Very good app!

The fan speed is not updating.
Is this a known problem?

Thanks!
Hei!
Status oppdateres - men viftehastighet vil ikke oppdatere.
Er det et kjent problem?

Veldig bra app ellers!

Mvh
Amund

If you could please keep the conversation in English as much as possible, then more people will be able to participate and help you. If you would rather not or can’t communicate in English then please check out Non-English boards at

https://community.athom.com/c/non-english

OK, thanks.

I will have a look at the issue.

Can you go to https://developer.athom.com/tools/devices and search for the systemair device.

Check the last updated for systemair_fan_mode_iam and systemair_fan_mode_iam_ro.

Yes:
2 weeks and the other 26minutes ago.
Picture:

And systemair_fan_mode_iam and systemair_fan_mode_iam_ro does not change, if you change the speed of the fan with the Systemair app ?

What if you change the speed with the Homey app ?

@balmli: Hi
I bought the Z-Wave unit from Systemair. What values can be retrieved from the unit with the app? -All modbus? Can values also be written to the unit?