Changelog:
2.7.0
- Add support for the Z-Smoke AC Smoke Detector device
2.6.0
- Add support for the Z-TEMP2 Thermostat device
- Update Thermostat device driver library
2.5.0
- Add support for the Z-TRM3 Thermostat device
- Add Meter Reset maintenance action for Z-TRM2fx, Z-Dim and Z-relay
- Update Homey meshdriver to v1.3.23
v2.4.2
- Add support for the Z-Push button 4 device
- Update app for new app store
- Update Homey meshdriver to v1.3.21
2.4.1 (BETA), Homey SW ≥2.4.0
- Finalize app and drivers for ‘Energy’ (Homey 3.0.0)
- Update Homey meshdriver to v1.3.14
v2.4.0 (BETA), Homey SW ≥2.4.0
- Add support for Heatit Z-Dim rotary dimmer
- Update Homey meshdriver to v1.3.9
v2.3.0 (BETA), Homey SW ≥2.4.0
- Fix S2 security handshake issues with Z-TRM2fx, Z-water and Z-Relay that result in Z-wave network stability issues by forcing non-secure inclusion.
- All users experiencing stability issues with the Z-TRM2fx, Z-Water and Z-Relay devices are advised to upgrade to v2.3.0 and remove and re-include their devices based on the v2.3.0 version
- Removed Homey 1.x.x mobile interface (obsolete)
- Add insights logging for the Thermostat state capability
- Prepared app and drivers for ‘Energy’ (Homey 3.0.0)
- Update Homey meshdriver to v1.3.6
v2.2.1
- Fix issue not being able to include the Heatit Z-push button 2 and Z-push button 8 devices
- Z-TRM2(fx) changed default temperature- and meter-reporting interval from 60 to 900 seconds to prevent Z-wave network lock-up
v2.2.0
- Add support for the Heatit Z-relay device
- Add support for the Heatit Z-DIN-616 device
- Update branding of the app
v2.1.2 (BETA)
- Fix temperature reporting issues for Z-wave thermostat (FW 1.92), Z-TRM2(fx) and Z-Water
Note: This fix only works as of Homey SW 2.0.5 ([Z-Wave] Reports from nodes with unknown Command Classes can now be read) and will not be implemented in Homey SW 1.5.x
Note : Please follow the steps mentioned below to fix the temperature reporting :
- For already paired devices:
- Go to advanced settings, and replace (add if not existing) Homey’s ID
1
with1.1
in the following association groups used for the temperature reporting:
- Z-wave thermostat (FW 1.92): Group 3, 4 and 5
- Z-TRM2(fx): Group 2 and 3
- Z-Water: Group 11, 12, 13 and 14
- For the thermostats, change in the Device specific settings (Sensor settings group), the ‘Displayed temperature’ to the sensor connected (default: floor sensor)
- Save settings
- Alternative option is to remove and re-include the device based on v2.1.2 of the app and Homey SW version > 2.0.5
- Add temperature changed flow cards for Z-wave thermostat (FW 1.92), Z-TRM2(fx) and Z-Water
- Update to meshdriver v1.2.32
v2.1.1 (BETA)
- Add support for the Z-Water regulator
- Update to meshdriver v1.2.30
- Note : due to an S2 issue within the Homey Z-wave core, the measured temperatures are not reported for the Z-wave thermostat (FW 1.92) and Z-TRM2(fx) thermostats as well as the Z-Water regulator. When this will be resolved, it is likely that the thermostat will need to be re-included
v2.1.0 (BETA)
- Add support for the Z-wave thermostat (FW 1.92)
- Add support for the Z-TRM2(fx) thermostat
- Add all remaining settings for the thermostats
- Add Power Regulator Mode action card for the Z-wave thermostat (use at own risk)
Note: due to an issue within the Homey Z-wave core, the measured temperatures are not reported for the Z-wave thermostat (FW 1.92) and the Z-TRM2(fx) thermostats. When this will be resolved, it is likely that the thermostat will need to be re-included
v2.0.2
- Add support for the Z-Push button 2 and Z-Push button 8 devices
- Minor (cosmetical) modifications to make the app Homey SW v2.0.0 compatible
v2.0.1
- Add thermostat onoff state trigger- and condition cards
v2.0.0
- SDK2 rewrite of the ThermoFloor / Heatit app
- SDK2 rewrite of the Multireg / Heatit Z-Wave thermostat device driver
- Update to meshdriver v1.2.28
Note: unfortunately, the set thermostat mode action card will be set to “comfort” mode after this update. The action card will need to be updated manually.